The Best Mercruiser 50 Cooling Hose Set

Water Pump (Standard)

An ACDelco Professional, premium aftermarket Engine Coolant Temperature Sensor is the high quality replacement ideal for many vehicles on the road today. It monitors the engine temperature. The engine temperature signal is used by the engine control module to adjust the air/fuel mixture and ignition timing. This premium aftermarket replacement engine coolant temperature sensor is manufactured to meet your expectations for fit, form, and function.

Specification:

Rated Voltage: DC 12V
Rated Power: 60W
Maximum Flow: 5L/min
Maximum Pressure: 0.8MPA
Pump Diameter: Approx. 4.8cm / 1.89inch
Length: Approx. 14.5cm / 5.7inch
Cable Length: Approx. 30cm / 11.8inch
Clips Length: Approx. 8cm / 3.15inch
Outlet PVC pipe Length:150cm
Nylon pipe Length:100cm
Brass pipe Length:70cm

Package include:

1x Oil Pump
1x 11mm Outlet PVC pipe
1x 6mm Nylon pipe
1x 5mm Brass pipe

How to use:
 1.Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil 
2.Then connect the pump to the power, run it for a while, and observe whether the inlet and outlet is normal
3.Next,open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move; then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely); as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again
4.After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean
If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out

Note: If you want to connect this pump to AC power, you will need a power converter.

Features and BenefitsAll-In One Auto Trunk Organizer with 3 huge compartments which includes one removable sub-divider for customization11 pockets in total to store smaller things – 2 large quality pockets, 8 Fabric pockets and 1 mesh pocket give you plenty of extra storage spaceWhen open, the size is 23.5″ (60 cm) * 15″ (37 cm)* 12 inches (12.5 cm). It is the ideal solution for all your supplies – One of the Largest, strongest and durable auto trunk organizers on the market with the customization of being able to fold in half for convenience and various job sizes.Sturdy side Walls and center divider to hold your organizer open and give strength even when emptyNon-skid feature to prevent your trunk cargo from moving around during travelRemovable sub-divider to allow you to organize and accommodate different job sizesThick PVC mesh Trunk Liner that can endure and withstand the wear and tear of vehicle useStrong Stiff base to provide bottom supportWhen folded in half, 14.6″ by 12.25″ by 1.5″, it is ideal storage container or seat organizer if you use it in shopping cart, car seat or picnic basket (car seat organizer, back seat organizer)Collapsible and folds flat to 1.5” and can be stored in drawer (see picture) or car compartments ✓ High Quality Durable Polyester that will last you a long timeHeavy Duty Eye Hole that you clip to the back of your truck (truck organizer)Strong, non-slip comfortable, heavy duty strap handles with grips to allow for easy transportEasy to use and carry: it is a space saver and allows for flexible space design when folded – it becomes a handbag when folded.Universal Fit – Fits all vehicles (truck, Suv, Van, Car) This professional premium organizer normally sells for $49 plus. It is absolutely risk-free with a 100% satisfaction guarantee. With limited stock, this organizer will not last. Get yours now while it is in stock.

These bellows and shutters are designed for the following MerCruiser applications: 1996-1999 V6 owners PLEASE LOOK AT PICTURE #2 Note: These will not work on V6 engines that came with the one piece manifolds (Use 807166A2 it has a flat tip), or early V8 with the round pin going through flapper. Used on many MerCruiser sterndrive V8 engines. (Some V6 that came with the two piece maniflold/elbow) For 1998 and newer engines, there are some 1996 and 1997 models that apply. There will be two rectangular holes for the grommets. If your Y-pipe has round holes you need the A3 water shutters. If your Y-pipe changes size a few inches bellow the shutter you have a one piece manifold V6 Y-pipe and need shutter A2.

Replaces 2 each of the Following:
807166A1 Water Shutters / Flappers 32-14358 , 32-14358T , 32-14358001 , 18-2746 Lower Exhaust Bellows , Tube , Hose，Clamp
32-44348 , 32-44348T , 32-44348001 , 18-2748 Upper Exhaust Bellows , Tube , Hose，Clamp
Fits many Mercruiser V6 and V8 engines Kit includes Two 4 inch upper hose bellows
replaces 32-44348 , 32-44348T , 32-44348001 Two lower exhaust hose bellows
replaces 32-14358 , 32-14358T , 32-14358001 Two Shutters replaces, 807166A1 Eight stainless steel clamps
Note:
These will not work on V6 engines that came with the one piece manifolds ( use 807166A2 it has a flat tip ) , or early V8 with the round pin going through flapper.
Used on many Mercruiser stern drive V8 engines. ( Some V6 that came with the two piece maniflold/elbow )
For 1998 and newer engines, there are some 1996 and 1997 models that apply. There will be two rectangular holes for the grommets. If your Y-pipe has round holes you need the A3 water shutters. If your Y-pipe changes size a few Inches bellow the shutter you have a one piece manifold V6 Y-pipe and need shutter A2.
If you have ever overheated these tend to get damaged. Sometimes you will find pieces of them in the exhaust when you remove the drive for servicing. They help keep water from entering the engine through the exhaust.